Title

Home
Articles Search
fuel filter

Articles search results for fuel filter

Showing 1 to 20 of 30 articles

The specter of 'unleaded fuel only' - instigated in UK on January 1st 1999 and seemingly from decades ago across the rest of the world - seems to be forcing more and more folk into frightened, panic orientated action. And Mini owners are featuring heavily in this. See bottom for useful part numbers. The situation not at all being helped by all sorts of conflicting information from 'leaned' sources, such as lead levels in humans has declined greatly since 1935 - despite the rapidly expanding ownership of petrol-burning vehicles. And benzene and toluene used in unleaded fuels are cancerous. Still, the powers that be are relentlessly forcing through the 'no heavy metals in fuel' bills, not being at all put off by such trivia. Not surprising bearing in mind the complete debacle on the catalytic converter front - the type decided on for world wide and universal use was developed and tested in California!

Cylinder Head - Unleaded Fuel Use

Engine - Identification Data Updated

If you have the engine tag still attached to the engine - just in front/below the thermostat housing - or perhaps the original engine number in the log book then the following should help you determine which engine you have. For Metro units, see 'Engine - Metro identification data'. Original engine identification numbers 850cc 8A Austin up to 25000 8MB Morris up to 25000 8AM Austin & Morris 25000 onwards 8AH Austin & Morris Automatic 8AJ Austin & Morris closed circuit breathing 8AK Austin & Morris automatic with closed circuit breathing 8WR Wolseley Hornet & Riley Elf 8AC Moke 85H/101 All variants 1969 onwards Note: third suffix letter denotes compression type, L = Low, H = High, e.g. 8AM/U/H101 denotes high compression. 998cc 9WR Wolseley Hornet & Riley Elf Mk2, pre closed circuit breathing 9AD Austin, Wolseley Hornet & Riley Elf Mk2 with remote type gearbox and closed

Engine - 998 Tuning, Bolt-ons

The 998cc engine is a very robust and tunable unit. It is also the most common engine found in standard Minis. See bottom for useful part numbers Terminology: MSC/MM - Mini Spares Centre/Mini Mania ID - Inside Diameter OD - Outside Diameter BBU - Big Bore Unit (refers to all 1275cc-based units) SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998) BHP - Brake Horse Power LCB - Long Centre Branch Despite the lure of the much-advertised 1380cc alternatives, many simply want to get a little more from what they have at reasonable outlay. The single biggest restriction on any standard Mini is the 'breathing apparatus' - anything that is connected to the induction and exhaust systems. The standard exhaust being the biggest culprit - it is desperately restrictive in the name of noise suppression and cheapness of manufacture. Oddly enough it also increases fuel consumption when tested over a better designed, fre

Engine - Running in Procedure

This is another of those subjects that crops up on the message board frequently. I am constantly surprised by the number of engine builders - or people who charge other folk for building engines at any rate - that never hand out such an information sheet. It seems pretty daft to me that having taken a wad of money off of a customer for an engine you've lovingly put together, you'd want to help that person get the very best out of the engine. And the running/breaking in procedure is absolutely crucial. It at least ensures no damage is incurred when the engine first bursts into life. A collection of the usual suspects have explained their own methods on the board, along with various others - many of which probably work just as well for them, a few which are down-right dubious. Following is a sheet I administer with every customer engine I build.

Injection - Tuning Update 03.14.03

This program of development embarked upon by myself and colleague Mike Barratt (MBE, Lincoln 01522 545189) was instigated by Keith Dodd, owner of Mini Spares centre. His instructions were for us ....

Air filtration - K&N Air cleaner test.

In the forefront of Mini tuning, improving the over-all breathing capability of the very asthmatic A-series the air filter set-up is one that sees priority attention. All the widely available (and widely varying) stage one tuning kits include at the very least a replacement - and hopefully - high-flow air filter element to fit into the standard plastic case,

In the past few years (well, must be nearly 6 years by now!) since I got involved with writing for the specialist Mini Magazines I have been continually fighting with the problem of limited space. This has limited what I have been able to cover, both in subjects and in details. Up until recently (say the past year or so) I have been covering fairly broad topics in a fairly broad terms and detail. Basically trying to cover perhaps the most popular areas dabbled in by the Mini owning masses.

Cylinder Head - Unleaded fuel use

Cylinder Head - Unleaded fuel use

The 998cc engine is a very robust and tunable unit. It is also the most common engine found in standard Minis. Despite the lure of the much-advertised 1380cc alternatives, many simply want to get a little more from what they have at reasonable outlay.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money.

DIY enthusiasts often believe that building an engine to give excellent all-round road performance is beyond them. Mainly from comparisons made between what they have been able to achieve and what specialists say should be achievable from any particular type of engine build.

Generally scrambled further by the non-perfect match of parts and components used between aforementioned specialist and erstwhile DIY-er, and the ritual 'nose-tapping and knowing winks' display of those specialists. Something you can very nearly 'see' even when talking to such folk on the phone - or that inimitable 'ah, yes, well…' So some form of 'black art' is implied. Whilst there is most definitely a degree of 'feel' involved between the real specialist's results and those of just a good engineer - the bones of the deal is subject to no such thing and is certainly within the capability of the DIY enthusiast given the necessary information. And that has been the problem.

Engine - Identification data

RUNNING IN NEW ENGINES

Install engine. It is absolutely imperative that the cooling system is more than sufficient to deal with any temperatures likely to be produced by the engine. More power means more heat to be dissipated. A standard radiator is very unlikely to be able to cope with a reasonable power increase over standard.

Do not fill cooling system yet. Set clutch throw-out and free-play take up. Double-check all connections electrical, oil, fuel and cooling system. Put in engine oil – use a cheap multi-grade mineral oil. DO NOT use either semi or full synthetic oils. They will stop the rings from bedding in. Remove spark plugs, and spin engine over in bursts of a few seconds to pick up oil pressure and prevent starter motor damage. DO NOT start engine until oil pressure picks up.

Once oil pressure is showing, check ignition timing statically. Set to figure advised by distributor maker, or if no figures available, set at around 6-8 degrees BTDC. Re-fit spark plugs a

The fuel situation seems to be worsening at a great pace these days. And as is exhibited by the questions that appear on the message board many folk are confused by what they can and can't do, and what is best to do as far as race engines go.

Many have posted (particularly from the States) that nothing need be done - just run on unleaded. They've been doing this for years and never had any problems. I have trouble believing that in the face of what I know and have investigated - so here's what the score really is.

Years ago this stuff called Tetraethyl lead was originally conceived as an octane enhancer. It was soon discovered, however, that the metallic oxides produced by the combustion process formed a protective coating on the valves and seats. This coating prevented micro welding of the valve seat to the corresponding seat in the head under high temperature operation.

Modern technology has seen dramatic improvements in power outputs over very recent years. Just look at Formula One, where 3000cc engines are now putting out the sort of power not even dreamed of not so long ago at rpm levels that make motorcycle engines flinch!

At the end of every racing season the new/recurrent champions are confirmed, and the rest of the field turning their attention towards next year/season and ways of beating the crowned champ. Invariably this involves that age-old quest for the illusive extra horsepower this year's champion seemed to have over everybody else. So I thought it may be useful to have a look at some stuff that is largely over-looked by many and to further agitate those little grey cells.

Modern technology has seen dramatic improvements in power outputs over very recent years.

Lubrication - Oil, what it does and how

It's criminal. Folk spend fortunes putting together super-sonic motors, only to skimp on the oil they use. Why? Oil's oil right? Wrong. Even if it's a standard engine, it deserves TLC considering it's extremely hostile working environment.

Oil is literally the engine's life-blood. The opening few sentences are astonishingly true. Oil isn't there just to prevent all metal components within an engine fusing together in the first few seconds of running, creating a total melt down of Chernobyl proportions. It's an intricate blending of chemicals to protect the engine as a whole.

The most commonly uttered statement about engine wear is most wear occurs within the first 10 minutes from start up when cold. True if cheap chip fat oil is used.In performance and race engines, a considerable amount of wear is created by heat, load, speed, and pressure. Again, cheapy oil won't give protection here.

General fitting instructions

To ensure correct installation of the AP Braking remote vacuum servo unit, thoroughly read and adhere to the fitting instructions prior to carrying out any work on the vehicle. Introduction The vacuum servo unit is incorporated into the hydraulic braking system, remote from the master cylinder, as an intermediate stage operating between the master cylinder and the brake assemblies. The two main parts of the servo unit consist of the vacuum servo mechanism and the hydraulic slave cylinder assembly.

These component parts are bolted together so that the slave cylinder piston is in line with, and is operated by, the servo push rod. A plastic no-return valve is fitted into the vacuum shell and an integral air cleaner is incorporated to prevent foreign matter entering the air control valve chamber. The servo unit is designed to give no assistance with very light brake application. In the absence of servo assistance due to loss of vacuum, an unres...

Mini Production dates

We have tried to get together as complete list as possible to show all the models made from 1985 onwards, hopefully this will help identify those cars that have been modified over the years. If you have any information that you know is correct or anything that you think is not right please let us know.

A very strange blog to write this one as after the joys of wining both the races at Snetterton.

The front brakes are standard Cooper 'S' 71/2" variety with the standard drums on the rear, with the assistance of a servo the rear regulator valve has been left out of the system and the brakes work very well. As the weight of the second engine amounts to the equivalent of two 11 1/2 stone passengers. Rear cooling is taken care of using a 1300 radiator mounted in the standard position. The heater take offs are connected to a 19 row oil cooler.

Articles search results for fuel filter

Contact Mini Spares

Store Details:

Classic Mini Brochure & Manuals